-- *******************************************************************
-- CISCO-POE-PD-MIB.my
-- Cisco Power Over Ethernet Powered Device MIB
--
-- March 2004, Francis Pang
--
-- Copyright (c) 2004 by Cisco Systems, Inc.
-- All rights reserved.
-- *******************************************************************
--CISCO-POE-PD-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Unsigned32FROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
TEXTUAL-CONVENTIONFROM SNMPv2-TC
SnmpAdminStringFROM SNMP-FRAMEWORK-MIB
ciscoMgmt
FROM CISCO-SMI;--********************************************************************
--* MODULE IDENTITY
--********************************************************************ciscoPoePdMIB MODULE-IDENTITYLAST-UPDATED"200405050000Z"ORGANIZATION"Cisco Systems Inc."CONTACT-INFO" Cisco Systems,
Customer Service
Postal: 170 West Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-poe@cisco.com"DESCRIPTION"This MIB is intended for devices powered by
external power sources, in particular Power
Over Ethernet (PoE or formerly called inline
power), to provide power usage configuration
and information for NMS. For example, PoE
supplies DC power over standard Category 5
unshielded twisted-pair (UTP) cable. Instead
of requiring wall power, powered devices such
as IP telephones can utilize power provided
from power source equipments. By using Cisco
Discovery Protocol (CDP), powered devices
can negotiated with power source equipment to
obtain optimum power supply.
GLOSSARY
Midspan Injector
The midspan PSE sends out a signal tone down
one of the unused pairs of the standard
Category 5 cable and detects tone on the
other unused pair when the PD loops this tone
back to it through a loopback transformer.
Once the midspan PSE detects this tone, it
begins to provide power down the cable using
the unused pairs. The midspan PSE provide no
physical layer capability.
Powered Device ( PD )
These are devices powered by external electrical
power sources. They are, for example, IP
telephones and wireless Access Points or bridges.
Power Source Equipment ( PSE )
These are devices supplying electrical power to
other equipments. They are, for example, inline
power switches and power patch panels."REVISION"200405050000Z"DESCRIPTION"Initial version of this MIB module."::={ ciscoMgmt 414}cpoePdMIBNotifications OBJECTIDENTIFIER::={ ciscoPoePdMIB 0}cpoePdMIBObjects OBJECTIDENTIFIER::={ ciscoPoePdMIB 1}cpoePdMIBConformance OBJECTIDENTIFIER::={ ciscoPoePdMIB 2}cpoePdInformation OBJECTIDENTIFIER::={ cpoePdMIBObjects 1}--********************************************************************
--* Textual Convention
--********************************************************************CpoePdPowerSourceType ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This is the type of power source equipment supplying
DC power to the PD.
pending -- power source is not yet determined.
acAdaptor -- power is supplied by an AC adapter
thirdParty -- power is supplied by a PSE not
supporting Cisco CDP
classic -- power is supplied and limited by
a classic Cisco PSE
midspan -- power is supplied by a midspan
injector
cdpNegotiated -- power is negotiated using Cisco
CDP
highPowerClassic -- power is supplied by Cisco
PSE without negotiation."SYNTAXINTEGER{pending(1),acAdaptor(2),thirdParty(3),
classic(4),midspan(5),cdpNegotiated(6),highPowerClassic(7)}--********************************************************************
--* Configurations and Information
--********************************************************************cpoePdCurrentPowerLevel OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This identifies the currently how much power
is consummed by the device at which this agent
is running. The level shall be one of the
cpoePdSupportedPowerLevel in the
cpoePdSupportedPowerTable."::={ cpoePdInformation 1}cpoePdCurrentPowerSource OBJECT-TYPESYNTAX CpoePdPowerSourceType
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This is the current power source type
obtained from device power source detection."::={ cpoePdInformation 2}cpoePdSupportedPowerLevelTable OBJECT-TYPESYNTAXSEQUENCEOF CpoePdSupportedPowerLevelEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table shows all the supported electrical
power consumption levels of this agent and the
corresponding modes of operation at those power
levels. The mode of operation and the device
capability changes as the supplied power level
varies. The number of supported levels is
platform and implementation dependent."::={ cpoePdInformation 3}cpoePdSupportedPowerLevelEntry OBJECT-TYPESYNTAX CpoePdSupportedPowerLevelEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"Each entry shows a supported power level
and the corresponding mode of operation."INDEX{ cpoePdSupportedPowerLevel }::={ cpoePdSupportedPowerLevelTable 1}
CpoePdSupportedPowerLevelEntry ::=SEQUENCE{
cpoePdSupportedPowerLevel Unsigned32,
cpoePdSupportedPower Unsigned32,
cpoePdSupportedPowerMode SnmpAdminString}cpoePdSupportedPowerLevel OBJECT-TYPESYNTAXUnsigned32(1..65535)
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This index uniquely identifies the supported
power consumption level."::={ cpoePdSupportedPowerLevelEntry 1}cpoePdSupportedPower OBJECT-TYPESYNTAXUnsigned32(1..65535)UNITS"milliwatts"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This is the electrical power consummed by
the device operating at this supported power
consumption level."::={ cpoePdSupportedPowerLevelEntry 2}cpoePdSupportedPowerMode OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This is a text string describing the mode of
operation or capability of the device at the
power consumption level. For example, the
comsumption level and corresponding mode should
look like these:
1 'Full power mode'
2 'Low power mode - dot11radio 0 disabled'
3 'Low power mode - dot11radio 1 disabled'
4 'Low power mode - dot11 radios disabled'."::={ cpoePdSupportedPowerLevelEntry 3}
--********************************************************************
-- Conformance information
--********************************************************************cpoePdMIBCompliances OBJECTIDENTIFIER::={ cpoePdMIBConformance 1}cpoePdMIBGroups OBJECTIDENTIFIER::={ cpoePdMIBConformance 2}--********************************************************************
--* Compliance statements
--********************************************************************cpoePdMIBCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION
"The compliance statement for the SNMP entities that
implement the ciscoPoePdMIB module."MODULEMANDATORY-GROUPS{
cpoePdInformationGroup
}::={ cpoePdMIBCompliances 1}--********************************************************************
--* Compliance Groups
--********************************************************************cpoePdInformationGroup OBJECT-GROUPOBJECTS{
cpoePdCurrentPowerLevel,
cpoePdCurrentPowerSource,
cpoePdSupportedPower,
cpoePdSupportedPowerMode
}STATUScurrentDESCRIPTION"This collection of objects provide information about
the supported electrical power level, current power
consumption, and mode of operation of this agent."::={ cpoePdMIBGroups 1}END